I-PEX 83007-100B-01-D CABLINE®-SS 40AWG/50Ω series ultra-thin coaxial cable bundle substitute

High-speed data transmission in TI industrial vision puts higher requirements on internal wiring.

With the continuous development of machine vision cameras, visual sensors, AI vision detection, and industrial automation equipment towards high resolution, high frame rate, and real-time processing, the data connection between cameras and processors, visual SoC, or acquisition circuits also needs to take into account high-speed transmission, spatial layout, and connection reliability. TI currently provides solutions for Machine Vision, including processors, AI accelerators, and high-speed communication interfaces. Some of its visual processors are also aimed at multi-camera, machine vision, and robotics applications. In such application environments, cables are not just simple "connection wires," but an important component affecting the high-speed signal transmission and structural design inside the device. The extremely thin coaxial cables have a coaxial shielding structure and can provide good signal isolation and spatial adaptation capabilities in high-speed differential signal connection scenarios. Therefore, they have good application adaptability value between the camera modules, visual acquisition boards, and processing platforms of TI's industrial vision-related equipment.

---

Extremely thin coaxial cables offer miniaturization and high-speed connection advantages in TI industrial vision equipment.

For industrial cameras and vision inspection equipment, the internal space of the camera module is usually quite compact, and the cables may also need to pass through pivot points, narrow structures, or be close to other high-speed circuits. The I-PEX CABLINE®-SS utilizes a 0.4mm pitch, vertical right-angle insertion and extraction, and horizontal outlet structure, combined with a narrow depth design. Official data indicates that its structure after connection is suitable for passing through smaller pivot point spaces. At the same time, the official high-speed test uses a 40PIN, AWG#40 Micro-Coaxial Cable, 45Ω, 100mm cable length, and GSSGSSG Pin Assignment for verification, and is aimed at 16Gbps/Lane high-speed data transmission applications. This means that for engineers, when designing high-speed camera linkages for TI industrial vision equipment, they can comprehensively consider extremely thin coaxial cable solutions from factors such as cable diameter, impedance, wire sequence, connector pitch, and overall machine space, rather than simply pursuing thinner cables. For purchasers, it is advisable to focus on specific material numbers, connector matching, cable specifications, and bulk supply capabilities.

---

I-PEX 83007-100B-01-D: 10PIN, 0.4MM Pitch TI Industrial Vision Cable Selection Reference

The specific product model introduced this time is I-PEX 83007-100B-01-D, which belongs to CABLINE®-SS 10P HARNESS. The official product page lists this model as 100mm, 1-1 wire sequence. According to the corresponding 83007C0 engineering drawing, this harness uses AWG#40, 50Ω Micro-Coaxial Cable, with a total length of 100.0±5.0mm, and wire position defined as 1-1. The connector model used at the end of the wire is 20373-R10T-06, which corresponds to CABLINE®-SS structure with 10PIN and 0.4MM pitch. I-PEX official materials also show that 20373-R10T-06 belongs to CABLINE®-SS 10PIN Plug Housing, suitable for specifications such as Micro-Coaxial Cable AWG40. For TI industrial vision equipment engineers, when selecting, it is important to check the interface definition at the camera end and the mainboard end, the number of 10PINs, 0.4MM pitch, 1-1 wire sequence, 100MM length, and actual impedance requirements; for procurement personnel, it should be avoided to only purchase according to "10PIN ultra-thin coaxial cable" and instead, complete checking of I-PEX 83007-100B-01-D and its matching connector model. Our company can provide: I-PEX 83007-100B-01-D compatible and alternative harness solutions, which can be developed for compatibility and mass production according to customers' actual equipment structure, wire length, wire sequence, and electrical performance requirements.

---

Selection, compatibility, and alternative solutions reference and suggestions

If 83007-100B-01-D is to be used for the compatible alternative development of TI industrial vision equipment, engineers are advised to first confirm the connector structure and PCB interface of the original equipment, and then further confirm the cable length, wire sequence, Micro-Coaxial Cable specification, impedance, and installation space. Particular attention should be paid to the fact that the 16Gbps/Lane and 45Ω AWG#40, 100mm specifications on the I-PEX CABLINE®-SS product page are specific high-speed performance test conditions and cannot be directly equated to the actual wire specifications of each CABLINE®-SS cable; for 83007-100B-01-D, the AWG#40, 50Ω, 100mm, 1-1 specifications marked on the corresponding 83007C0 engineering drawing should be an important basis for alternative development. Additionally, according to the current official information of I-PEX, CABLINE®-SS has specifications of 10, 14, 20, 30, 32, 35, 40, and 50PIN, etc. Therefore, if customers have different PIN numbers or length requirements in the future, they can also carry out corresponding development according to the actual device interface, rather than simply applying parameters from other models.

---

Make the ultra-fine coaxial cable better match TI industrial vision equipment
TI industrial vision systems are developing towards multi-camera, high-speed image transmission, AI vision processing, and equipment miniaturization, which puts more stringent comprehensive requirements on internal high-speed cables. TI's machine vision solutions cover vision cameras, vision sensors, and high-speed communication and processing capabilities. Meanwhile, I-PEX CABLINE®-SS offers a connection platform for engineering design evaluation with its 0.4MM spacing, narrow structure, and Micro-Coaxial Cable connection solution, providing compact high-speed equipment with a choice for engineers to evaluate. As the CABLINE®-SS ultra-fine coaxial cable with 10PIN, 100MM, and 1-1 wire sequence, I-PEX 83007-100B-01-D is matched with the 20373-R10T-06, 10PIN, 0.4MM spacing connector, and is suitable for evaluating cable selection and compatibility for alternative development in industrial cameras, machine vision, vision acquisition, and edge AI equipment. For engineers, the focus should be on high-speed signal integrity, impedance, wire sequence, and structural space.【3W Electronic Components Network】Professional customization and production of extremely fine coaxial cable assemblies and matching connectors, terminals, and board-to-board connectors. If you need technical evaluation or project cooperation, please contact:Manager Zhang 18913228573 (WeChat same number)For purchasing personnel, it is crucial to focus on material numbers, connector specifications, quality consistency, delivery cycle, and compatibility with alternative options, thereby achieving a balance between performance and supply chain requirements.