Categorization：Harness Component
When selecting ultra-fine coaxial cable assemblies internally in electronic devices, the number of pins is not the more, the better, but should be determined according to the actual signal quantity, differential channel number, power and ground configuration, and connector space required by the device. The I-PEX CABLINE®-SS series offers specifications such as 10, 14, 20, 30, 32, 35, 40, 50 pins, using a 0.4mm pitch and vertical right-angle structure, suitable for high-density internal connections. For engineers, if the device only requires a few signal channels, they can choose cable assemblies with fewer pins to reduce space occupation; if it involves eDP, MIPI, USB, HDMI, or other multi-channel high-speed signals, then calculations need to be made according to the actual Lane number, auxiliary signals, power, and GND distribution, and enough pins should be reserved. Purchasers should note that the number of pins, connector model, and wire sequence are interrelated, and cannot be purchased solely based on "32Pin" or "40Pin".
This product corresponds to I-PEX 83020-100B-01-D, which is a CABLINE®-SS 32Pin, 0.4mm Pitch, AWG#40, 200mm, 1-1 thin coaxial cable assembly. The connector model used at the cable end is 20373-R32T-06. According to the I-PEX official model information, the 32Pin CABLINE®-SS has both 1-N and 1-1 cable assembly schemes, among which the 1-1 series includes 83019 (100mm), 83020 (200mm), and 83021 (300mm). Therefore, when engineers choose the 32Pin scheme, they not only need to confirm whether "32Pin is enough", but also further confirm whether Pin-to-Pin straight-through is required at both ends, whether the cable length matches the device routing, and whether the AWG specification meets the design requirements. For the 83020-100B-01-D, the corresponding cable end connector 20373-R32T-06 can be compatible with AWG#40 Micro-Coaxial Cable, suitable for internal cable assembly design of equipment requiring high-density, multi-channel signal connections.
CABLINE®-SS covers a relatively complete range of Pin numbers from 10Pin to 50Pin, such as 10P, 14P, and 20P, which are suitable for relatively simplified multi-channel connections. 30P, 32P, and 35P can meet the needs of higher numbers of signal channels, while 40P and 50P are suitable for internal connections of high-speed devices with more channels. The official cable data also provides 1-N and 1-1 structures, such as 32Pin corresponding to 1-N models such as 82887/82442/82888, as well as 1-1 models such as 83019/83020/83021. When selecting actually, engineers should first count the high-speed differential pairs, control signals, power, and ground lines according to the schematic diagram, determine the required Pin number, and then judge in combination with the connector width, PCB space, wiring direction, and internal bending path of the device; purchasers should take Pin number, wiring sequence, length, AWG, and connector material number as complete procurement conditions. For high-speed applications, it should be noted that the official high-speed test of CABLINE®-SS is performed under the conditions of 40Pin, AWG#40, 45Ω, 100mm, GSSGSSG for the 16Gbps/Lane application reference, so the reference result cannot be simply equated to the actual performance of cables with all Pin numbers and all lengths.
If the original equipment uses the I-PEX CABLINE®-SS series, when considering domestic substitution or second supplier introduction, it is recommended to prioritize item-by-item verification according to the order of "Pin number→Connector→AWG→Length→Wire sequence→Signal requirements". Taking 83020-100B-01-D as an example, the core substitution conditions should focus on matching with 32Pin, 0.4mm Pitch, 200mm, 1-1, AWG#40, and the 20373-R32T-06 wire harness connector; if the customer's actual project adjusts from 32Pin to 30Pin, 35Pin, or 40Pin, it cannot be substituted simply by changing the number of wires. It also requires simultaneous confirmation of the connector components, PCB terminal sockets, wire sequence, and mechanical dimensions corresponding to the Pin number. According to I-PEX official data, different Pin numbers of CABLINE®-SS have corresponding connector and Harness models, so substitution development should be based on specific material numbers for verification. Our company can provide: I-PEX 83020-100B-01-D compatible substitution cable solutions, which can match and customize ultra-fine coaxial cable assemblies according to the customer's equipment Pin number, length, wire sequence, AWG, and actual installation space.
“Without the consent or authorization of this site, no one shall reproduce, reprint, distribute, cite, change, broadcast or publish the content in whole or in part in any form, nor shall there be any other violation of the copyright of this site.
